FAT-60-16-1U
FAT-60-16-1U is a new generation, enhanced SDH / MSTP device. It is a carrier-class, high compact platform and aimed for metro and SDH networks access. It can work as Add-Drop Multiplexer (ADM), Termination Multiplexer (TM), and also as a Gigabit Ethernet to SDH converter.
FAT-60-16-2.5U
FAT-60-16-2.5U is extreme high compact and powerful MSTP equipment, it integrates all kind of transport platforms, such as IP Ethernet, SDH, PDH, DDN, PCM all together; supports all type of digital services, such as digital cross connect (DXC), IPPBX, voice/data drop/insert services all-in-one on a 2.5U height, 19 inches width equipment shelf.
FAT-60-16-3.5U
This manual mainly introduces the product characteristics, operating principle, system features and performance indexes of FAT-60-3516 MSTP Multi-service tansfer platform, while for the planning designers and users to application this series of products provides a general introduction, it includes a variety of networks can be composed of this series of products
FAT-60-3516 adopts high-speed 2.5Gbit/s backplane buses and high capacity cross-connect matrix, which greatly enhance the efficiency and reduce the overall size of the system.
FAT-50E-16E1
FAT-50E-16E1 PDH is point-to-point transmission equipment operating at 150Mb/s bit rate.
FAT-50 GE
FAT-50GE Equipment is optical transmission equipment, it can realize the 4/8/16 E1s and 1000Mbps Ethernet date channel transmission over optical line of 1.25Gb/s, the four 1000Mbps Ethernet date channel share 1000M bandwidth.
FAT-50E-4/8E1
FAT-50E-4/8E1 Equipment is point-to-point transmission equipment operating at 150Mb/s bit rate. It adopts 1U high standard 19″ rack. It is composed of 1+1 optical interfaces, 4 E1 interfaces, 4 electrical ETH interfaces, 1 EOW interface,1 RS232 NMS interface,1*Ethernet NMS port, support dual power:220AC and -48DC.
FAT-50E-4E1 /1ETH
This model applies reverse multiplexing technology to transfer10M/100M Ethernet data by using E1s. It realizes conversion between 1to 4 E1 channels and Ethernet interface (fiber or copper). It is capable of providing a real Ethernet throughput of 8Mbps respectively. And it also automatically adapted to lower data rates from 2Mbps, in case that less E1 circuits is employed.
FAT-50E-4E1/4ETH
This model applies reverse multiplexing technology to transfer transfer10M/100M Ethernet data by using E1s. It realizes conversion between 1 to 8 E1 channels and Ethernet interface. It is capable of providing a real Ethernet throughput of 16Mbps respectively. And it also automatically adapted to lower data rates from 2Mbps, in case that less E1 circuits is employed.
FT50-T3-PBX
FT50-T3-PBX is an intelligent E1 channel auto protection switch (i-APS) that acquires a standard 19″ / 1.5U height chassis, and supports 1+1 dual power, for maximum of 8 E1 channels protection.
FAT-50 IP-PBX
FAT-50 IP-PBX is a new generation of IPPBX multimedia exchange platform .It is based on Fatech’s R & D and production technology accumulation, through market research, it fully absorbs the advantages of domestic and overseas digital switch. It adopts embedded technology and modular design, and in accordance with the requirements of the embedded technology, ITU-T recommendation technology, using FPGA technology, chip technology.
FAT-50P-56-5U
FAT-50P-56-5U is a high capacity i-APS (Intelligent Auto Protection Switch) provides the most valuable data services with extreme high availability for the bank, military or government department.
FAT-10C-1/2/4/8D
FAT-10C-1/2/4/8D Desktop TDM over IP will transmit E1 signal through IP channel, the IP channel can be existing wired Ethernet channel or wireless Ethernet channel.
FAT50T1-IP
FAT50T1-IP PCM is 1U high, 19 inch width equipment .It not only be PCM, but also can be PDH or VOIP equipment.
FAT-50C-1/4/8/16D
FAT-50C-1/4/8/16D TDM OVER IP Equipment will transmit E1 signal through IP channel, the IP channel can be the existing wired Ethernet channel or wireless Ethernet bridge channel.
FAT-50 T2
PCM Equipment adopts 1U high standard 19 inch rack. It is composed of one HDSL uplink interface, 4 E1 interfaces(it can be set as downlink or uplink by NMS), 2 uplink optical interface, 32 channels service access interfaces, 1 uplink electrical Ethernet interfaces and 4 downlink electrical Ethernet interfaces and one ETH NMS interface, one alarm interface.
The maximum 64Kbps access capacity of FAT50-T2 PCM equipment is 256X256.
FAT50-T3
FAT-50T3 Equipment adopts 1.5U high standard 19″ inch rack. The maximum 64Kbps access capacity is 32.
FAT-50T5-1U
FAT-50T5-1U is a new generation, enhanced SDH / MSTP device. It is a carrier-class, high compact platform and aimed for metro and SDH networks access. It can work as Add-Drop Multiplexer (ADM), Termination Multiplexer (TM), and also as a Gigabit Ethernet to SDH converter.
FAT50-T 5U , 9U
FAT50-T 5U , 9U Digital Cross-connection equipment adopts 9U high standard 19″ rack. It supports multiple analog and data access, and fiber/electronic integration. The maximum 64Kbps access capacity of PT-70 9256 Digital Cross-connection equipment is 240, and the maximum E1 access capacity is 240 as well.
FAT-50E-4ETH-Fiber
This serie product can realize the conversion between 10/100Base-T and fiber,mainly used in transmission of optical fiber long distance(20/40/60/80/120km), totally support the speed of10/100M or 10M, 100M. The optical and electrical interfaces all can work under 10M or 100M.
FAT-50T-10-2.5U
FAT-50T-10-2.5U adopts 2.5U height standard 19″ rack mountable chassis for exchange office. The powerful switching matrix provides 256 x256 non-blocking cross connections. System supports maximum 96 x E1, and 96 x 64Kbps channels with the expansion chassis. Various network cards, such as PDH, E1 and TDMoIP (Ethernet) uplink card are available for fitting different networks requirement.